The Radio Control Club of Detroit

An AMA Gold Leader Club
AMA Chapter # 368
An AMA Charter Club Since 1953
IMAA Chapter #206

Schedule

Join RCCD

Events Only

News Archive

Contact RCCD


RCCD 2011 Scratch Build Project - Components

Project Home
Instructions
Tips
Plans & Drawings
Wood & Hardware
Member project pics
Contacts

This page contains the wood list, wood lay-outs that will be used, and a suggested hardware list.


Note: You can either purchase the wood listed from RCCD ($70), or provide your own in the same sizes. Either way, it will be laser cut and shaped for you.


    RCCD Ugly Stick Project 2011    
    Wood Material List -- Rev. 12-01-10  
      Wing      
             
Description part # material quantity   cost total
         
 
19 Ribs, top back 1563 1/8x6x48 2 balsa 4.03 8.06
2 Tips & 4ribs 1548 1/4x4x48 1 balsa 3.16 3.16
String spars 1075 1/4x1/4x36 8 balsa 0.33 2.64
Main spars 5558 1/4x1/2x36 5 spruce 1.03 5.15
Sheeting 1132 3/32x3x36 14 balsa 0.83 11.16
Cap strips 1025 3/32x1/4x36 5 balsa 0.21 1.05
Leading edge 1077 1/4x1/2x36 2 balsa 0.44 0.88
Trailing edge 1078 1/4x3/4x36 2 balsa 0.64 1.28
             
             
      Fuselage    
             
Bottom rear fuse 1163 3/32x6x24 1 balsa 2.11 2.11
Fuse sides,former 1565 1/4x6x48 2 balsa 5.58 11.16
F2,f/w,bot reinforce 6185 1/4x12x24 1 ply 5.31 5.31
Bottom frt fuse 6243 3/32x12x24 1 ply 7.46 7.46
Triangle 1925 1/2x1/2x36 2 balsa 0.69 1.38
             
             
      Misc      
Rudder,Fin,Stab, 1146 1/4x4x36 2 balsa 2.49 4.98
Ailerons,elevator, 1135 1/4x3x24 2 balsa 1.54 3.08
hatch            

Pre-Cut Components

 

Ugly Stick Project
Suggested Hardware List for each plane

* 10 or 12 oz fuel tank
* fuel tubing (approx. 2 ft.)
* fuel filler tap (optional)
* motor mount/nose gear mount
* bolts & 'T' nuts for mounting motor mount to firewall
* bolts to mount motor to motor mount
* main landing gear
* bolts, washers, lock washers, to mount main gear to fuse
* axles for main gear
* nose gear or tail wheel gear
* wheels (2 main -3” to 3 1/4” dia. & 1 nose - 2 3/4” dia. or 1” dia. tail wheel)
* wheels collars 6 pcs for wheels
* wheel collars for nose gear shaft--if applicable
* 1/4-20 nylon bolts for wing hold down 2pcs
* 1/4-20 “t” nuts for wing hold down 2 pcs
* large control horns 4 pcs
* 2-56 metal push rods 12” (cut to size) 2 pcs aileron
* 2-56 metal push rods 12” (cut to size) 2 pcs rudder & elev
* 2-56 flex cable type push rods 24” 2 pcs throttle & (steering nose gear)
* 1/4” dia wood dowels for push rods & wing dowels 2 pcs
* quick connectors for 2-56 metal push rods 5 pcs
* CA hinges 17 pcs
* small wood screws for mounting servoes, servo hatch covers approx 50 pcs
* C A glue –Thin & gap filling 1 large bottle each
* covering

 


RCCD
HOME


Project Home

njh